Mechanical

Price per 1.

Price per 1.

Performance Head Gasket with steel locating dowels.

The standard K series head locating dowel is made from plastic, this can allow movement between the head and block and eventually headgasket failure. When this occurs replace the standard item with this CNC machined component made to exacting tolerances to enable a positive loaction between head and block.

Clutch Slave Cylinder, an original equipment part. RRP £59.95

Required when changing cambelt or removing crank pulley. Prevents rotation of engine.
Locate in starter motor position.

**NEW LOWER PRICE**

Contains all the relevant gaskets when replacing a head gasket.

Contains all the relevant gaskets when replacing a head gasket.

Kit consists of:
Latest Multi Layer Shim Landrover Head Gasket
Cam Cover Gasket
Cam Seals
Stem Seals
Inlet Gasket
Plenum Gasket
VVC Seals
HCU Seals
Exhaust to Head Seals
Water Elbow Gasket
Thermostat Seal
Dowels

Inlet manifold to plenum gasket. Part Number - LKJ100860

Inlet manifold gasket for the VVC model. Part Number - LKJ100821

SPECIAL OFFER - WAS £104.20 NOW £75.00

Crossgate upper section for both MGF and TF models. Part Number - ULS100060.

Left to Right Gearstick Movement.

**NOW ONLY £75 - SPECIAL OFFER - REDUCED FROM £105.00**

Lower gear cable for the MGTF model. Part Number - ULS000010.

**PREVIOUSLY UNAVAILABLE**

Replacement part for the gearbox end of the gear cable.

Advise: When changing the Gear Cable Gaiters check the Gear Cable Retaining Clip as these can work loose and cause gear selection problem. To replace see ET7232 Gear Cable Retaining Clip

Trophy 160 oil filter housing. This housing allows fitment of oil cooler take off pipes. Can be retro-fitted to all K-series engines.
NOTE: Currently developing oil cooler kit in conjunction with this item.

Required when replacing the head gasket. These "stretch bolts" bolt through the head into the ladder rail literally holding the engine together.

**REDUCED PRICE FROM 23/03/10**

******WAS £104 NOW ONLY £80******

Direct replacement for the standard rover part for 1.8 engines. Rover part number NAD 101340 - Manufacturer Bosch.

The standard MG wiper linkage will eventually wear out and need replacing, rather than use the standard part we have re-engineered the linkage using stronger and longer lasting components. All the parts that can wear out can be replaced at a later date from our stock, we doubt that you will need to replace the new design, as the parts are substantially better. Please Note: This item will fit both left and right hand drive vehicles. This item designed by Mike Satur. If you see it sold elsewhere it is a copy.
Fitting instructions are included with the kit - please note that fitting will take approx. 1-1.5hours.
**OFFER ** £39.00 + Vat. a saving of £6.00

Please Note: Price per set of 16

SPECIAL LIMITED HALF PRICE OFFER
PAIR REAR LH & FRONT RH
Was £500 now £250, limited stock available at this price.
Variable valve control units.
Fits to cylinder head, controls nlet camshafts left hand side and right hand side.

Variable valve control unit. Fits to cylinder
head, controls inlet camshafts left hand side.

Used VVC inlet camshafts available from £60.00 each.

Variable valve control unit. Fits to Cylinder
head, controls inlet camshafts right hand side.

Used VVC inlet camshafts available from £60.00 each.

For VVC model only. 8 per cylinder head. Price per 1.

Gear box bell crank assembly.
Upgraded part. Improves gear selection.
(please note 2 rod ends supplied with this kit)

SPECIAL VALENTINES OFFER was £125 not £90
LXS100080
Genuine Hydraulic Control Unit with actuating solenoids

Replace if loose as can cause gear selection problems.

2 per car required.